Summasketch II

Status
Not open for further replies.

Don D

Usenet Archive
Joined
Nov 29, 2001
Messages
1
Reaction score
0
Can anyone please provide advice for installation/configuration of this digitizing tablet under Microstation J under Windows '98SE. I have downloaded the Bentley driver WTI20R40, and installed it according to their instruction (on two different machines, JIC) but Win & Microstation simply refuse to recognize the device exists. Any suggestions would be appreciated.

As an IT tech, I do not normally follow this group: please copy any response to my mail address below. TIA

Don
 
It may be a com port problem. An earlier tablet required to force the com port, particularly if it is defaulting to com two or four.

Best of Luck,

TFPierce
 
I have also found that a Summasketch to has power up problems. If you don't turn things on and off in the proper order it will not work. What I have found is that you must power everything off, power on the board, then power on the computer. If you do not power down the board when you power off the computer at night, it will not work when you turn the computer back on.

FYI,

Rh

"Don D" wrote:

Can anyone please provide advice for installation/configuration of this digitizing tablet under Microstation J under Windows '98SE. I have downloaded the Bentley driver WTI20R40, and installed it according to their instruction (on two different machines, JIC) but Win & Microstation simply refuse to recognize the device exists. Any suggestions would be appreciated.

As an IT tech, I do not normally follow this group: please copy any response to my mail address below. TIA

Don
 
I think you have to try a different driver.

Windows has to recognise it first.

Try this site for drivers not Bentley

http://www.gtcocalcomp.com/supportsummasoftware.com

"Don D" wrote:

Can anyone please provide advice for installation/configuration of this digitizing tablet under Microstation J under Windows '98SE. I have downloaded the Bentley driver WTI20R40, and installed it according to their instruction (on two different machines, JIC) but Win & Microstation simply refuse to recognize the device exists. Any suggestions would be appreciated.

As an IT tech, I do not normally follow this group: please copy any response to my mail address below. TIA

Don
 
I think you have to try a different driver.

Windows has to recognise it first.

Try this site for drivers not Bentley

http://www.gtcocalcomp.com/supportsummasoftware.htm

"Don D" wrote:

Can anyone please provide advice for installation/configuration of this digitizing tablet under Microstation J under Windows '98SE. I have downloaded the Bentley driver WTI20R40, and installed it according to their instruction (on two different machines, JIC) but Win & Microstation simply refuse to recognize the device exists. Any suggestions would be appreciated.

As an IT tech, I do not normally follow this group: please copy any response to my mail address below. TIA

Don
 
If my feeble memory serves me right..... if you are going to use a digitizing tablet on your system, you must make it the only pointing device available to your system...... in other words.... unplug your mouse and store it in a closet somewhere..... the puck on the digitizing tablet will be your new mouse........

Cary

Don D wrote:

Can anyone please provide advice for installation/configuration of this digitizing tablet under Microstation J under Windows '98SE. I have downloaded the Bentley driver WTI20R40, and installed it according to their instruction (on two different machines, JIC) but Win & Microstation simply refuse to recognize the device exists. Any suggestions would be appreciated.

As an IT tech, I do not normally follow this group: please copy any response to my mail address below. TIA

Don
 
You can eliminate this problem by disabling the bios scanning of the serial port. It's been a few years, so I can't remember exactly how I did it, but just start poking around in the bios. How dangerous can it really be?

"RoadHog" wrote:

I have also found that a Summasketch to has power up problems. If you
don't
turn things on and off
in the proper order it will not work. What I have found is that you must power everything off, power on the board, then power on the computer. If you do not power down the board when you power off the computer at night, it will not work when you turn the computer back on.

FYI,

Rh

"Don D" wrote:
...
 
Fiddling with the Bios is not a problem these days Dan on latest motherboards. Mind you it used to be but you can just "Load defaults" if something goes wrong.
 
Defaults are for wussies. Stick a screwdriver in there and keep stirring it around until it works.

"SamuelG" wrote:

Fiddling with the Bios is not a problem these days Dan on latest
motherboards. Mind you it
used to be but you can just "Load defaults" if something goes wrong.
serial
> port. It's been a few years, so I can't remember exactly how I did it,
but
> just start poking around in the bios. How dangerous can it really be?
>
>
> "RoadHog" wrote:
>
> > I have also found that a Summasketch to has power up problems. If you
> don't
> > turn things on and off
> > in the proper order it will not work. What I have found is that you
must
> > power everything off, power on
> > the board, then power on the computer. If you do not power down the
board
> > when you power off the
> > computer at night, it will not work when you turn the computer back
on.
> >
> > FYI,
> >
> > Rh
> >
> > "Don D" wrote:
> >
> > > Can anyone please provide advice for installation/configuration of
this
> > > digitizing tablet under Microstation J under Windows '98SE. I have
> > > downloaded the Bentley driver WTI20R40, and installed it according
to
> > > their instruction (on two different machines, JIC) but Win &
> > > Microstation simply refuse to recognize the device exists. Any
> > > suggestions would be appreciated.
> > >
> > > As an IT tech, I do not normally follow this group: please copy any
> > > response to my mail address below. TIA
> > >
> > > Don
> > >
> > >
> >
> >
...
__

http://www.binaries.net
 
Status
Not open for further replies.

Latest threads

Back
Top